Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Высокие технологии Removal
просмотров - 195

C On VVT-i engines, the oil pressure switch is above the oil filter location

Align the flats on the crankshaft with the flats on the pump rotor

Engine in-car repair procedures 2A•21

14.2a On 1.3 litre Non-VVT-i engines, the 14.2b On 1.6 litre Non-VVT-i engines, the
oil pressure switch is located at the left- oil pressure switch is at the right-hand end
hand end of the cylinder block (arrowed) of the cylinder block (arrowed)

3 Unscrew the switch from the engine block. Be prepared for oil spillage.

4 Prior to refitting, apply a little Loctite Three Bond 1344 (or similar) to the threads of the switch.

5 Refit the switch and tighten it to the specified torque.

6 Reconnect the wiring plug.

15 Flywheel/driveplate -

removal and refitting

1 Remove the transmission as described in Chapter 7A or 7B.

2 Remove the pressure plate and clutch disc (Chapter 6) (manual transmission vehicles).

3 Use a centre punch or paint to make alignment marks on the flywheel/driveplate and crankshaft to ensure correct alignment during refitting (see illustration).

4 Remove the bolts that secure the flywheel/driveplate to the crankshaft. If the crankshaft turns, wedge a screwdriver in the ring gear teeth to jam the flywheel, or use a tool to lock the flywheel in position (see illustration).

5 Remove the flywheel/driveplate from the crankshaft. Since the flywheel is fairly heavy, be sure to support it while removing the last bolt. Some automatic transmission equipped vehicles have spacers on both sides of the driveplate (see illustration). Keep them with the driveplate.

Warning: The ring gear teeth may be sharp, wear gloves to protect your hands.


Читайте также


  • - Removal

    1 Relieve the fuel system pressure (see Chapter 4A). 2 Remove the battery as described in Chap-ter 5A, then lift out the plastic battery tray. 3 Remove the bonnet as described in Chap-ter 11. 4 Remove the air cleaner assembly (see Chapter 4A). 5 Raise the vehicle and support it securely on axle stands. Drain the cooling system and engine oil and remove the drivebelts (see Chapter 1). 6 Clearly label, then disconnect, all vacuum lines, coolant and emissions hoses,... [читать подробенее]


  • - Removal

    1 Block the rear wheels and set the handbrake. 2 Loosen the nuts on the right front wheel and raise the vehicle. Support the front of the vehicle securely on axle stands (see Jacking and vehicle support). Remove the right-handfront road wheel. 3 Remove the auxiliary drivebelt(s) as described in Chapter 1. To improve access, out and the smooth side is next to the belt. 11 If you plan to re-use the timing belt, apply match marks on the sprocket and belt and an arrow... [читать подробенее]


  • - Removal

    40 Remove the distributor (see Chapter 5B). Remove the timing belt and camshaft sprocket (see Sections 5 and 9). 41 Measure the camshaft thrust clearance (endfloat) with a dial indicator (see illustration).If the clearance is greater thanthe service limit, renew the camshaft and/or the cylinder head. 42 Position the knock pin in the exhaust camshaft just above the top of the cylinder head (see illustration). This will position the intake camshaft lobes so the camshaft will be pushed up... [читать подробенее]


  • - Removal

    Remove any components until the system has been discharged. Air conditioning refrigerant may only be discharged by a dealer service department or an automotive air conditioning specialist. Always wear eye protection when disconnecting air conditioning system fittings even after the system has been discharged. Air conditioning condenser - removal and refitting Warning: The air conditioning system is under high pressure. Do not loosen any hose fittings or 1 Have... [читать подробенее]


  • - Removal

    B . . . then release the clips and disconnect the heater hoses from the bulkhead stubs To prevent accidental deployment (and possible injury),turn the ignition key to LOCK and disconnect the negative battery cable whenever working near airbag components. After the battery is disconnected, wait at least two minutes before beginning work Refitting 6 Refitting is the reverse of removal. Check for proper operation. 10 Heater matrix -removal and refitting ... [читать подробенее]


  • - Removal

    A Remove the two screws in the heater knob recesses (arrowed)... 11 Heater and air conditioning control assembly-removal and refitting 1 Remove the rear section of the centre console (see Chapter 11). 2 Pull off the control knobs, and the air recirculation knob. 3 Undo the two screws in the knob recesses, the carefully pull away the centre cluster finish panel. Disconnect the wiring plugs as the panel is removed (see illustrations). 4 Pull up the driver's... [читать подробенее]


  • - Removal

    A Carefully lever the oil sump away from the block Remove the front bolts of the chassis brace (arrowed) Cylinder head bolts tightening sequence - VVT-i engines All engines VVT-i engines 27 Install the cylinder head bolts and washers, then tighten them in sequence to the Stage 1 torque setting (see illustration). 28 Angle tighten the bolts a further 90° in sequence. 29 Check and adjust the valve clearances as necessary (see... [читать подробенее]


  • - Removal

    Undo the two bolts (arrowed) and remove the hose bracket 19 Road test the vehicle and check for proper operation of all accessories. 14 Exhaust manifold -removal and refitting Warning: The engine must he completely cool before beginning this procedure. 1 Remove the upper heat shield from the manifold (see illustration). Note: There may also be a lower heat shield, but this is attached to the manifold from underneath and does not need to be removed. 2 Apply... [читать подробенее]


  • - Removal

    Litre 4E-FE engine Camshafts and followers Carefully prise the oil seal out with a screwdriver engine mounting and the socket to press the seal in (see illustration). 6 Refit the camshaft sprocket and timing belt (see Section 5). Refer to Section 4 and refit the cylinder head cover. 7 Run the engine and check for oil leaks at the camshaft seal. - removal, inspection and refitting Note:Before beginning this procedure, obtaintwo 6x1.0... [читать подробенее]


  • - Semi-detached, estate-agent, terraced, condition, builder, detached, removal, surveyor, spacious, cramped, architect

    For at in on of into with She wanted a place ………….her own. He’ll move ………….tomorrow. He’ll move………….his new flat tomorrow. I share the kitchen…………three other people. The landlord asked the tenant…………. more rent. My flat is ………….the top floor. My flat is………….a modern block. The house is …………good condition. I looked ………….advertisements………….the newspaper. She pays a rent……..£90 a... [читать подробенее]