Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Высокие технологии Removal
просмотров - 187

Remove any components until the system has been discharged. Air conditioning refrigerant may only be discharged by a dealer service department or an automotive air conditioning specialist. Always wear eye protection when disconnecting air conditioning system fittings even after the system has been discharged.

Air conditioning condenser

- removal and refitting

Warning: The air conditioning system is under high pressure. Do not loosen any hose fittings or

1 Have the refrigerant discharged and recovered by a Toyota dealer or automotive air conditioning repair facility.

2 Undo the three screws and remove the radiator grille.

3 Disconnect the condenser inlet and outlet fittings (see illustration). Cap the open fittings immediately to keep moisture and contamination out of the system. Discard the O-ring seals, new ones must be fitted

Note:On pre October '99 models, the left-
side fitting is connected to the receiver/
drier (see Section 13), on models after this
date, the receiver/drier is integral with the
condenser.      

4 Undo the bolts securing the pipe support brackets to the condenser (see illustrations). 5 Undo the bolts for the upper and lower condenser supports on both sides (see illustrations).

6 Undo the radiator upper support bolts, and push the top of the radiator backwards - there is no need to disconnect the hoses.

7 Push the radiator back towards the engine,

3•12 Cooling, heating and air conditioning systems

15.4a Condenser pipe support bracket bolt (arrowed) - right-hand side. . .

the lift the condenser upwards from place

(see illustration).


Читайте также


  • - Removal

    1 Relieve the fuel system pressure (see Chapter 4A). 2 Remove the battery as described in Chap-ter 5A, then lift out the plastic battery tray. 3 Remove the bonnet as described in Chap-ter 11. 4 Remove the air cleaner assembly (see Chapter 4A). 5 Raise the vehicle and support it securely on axle stands. Drain the cooling system and engine oil and remove the drivebelts (see Chapter 1). 6 Clearly label, then disconnect, all vacuum lines, coolant and emissions hoses,... [читать подробенее]


  • - Removal

    1 Block the rear wheels and set the handbrake. 2 Loosen the nuts on the right front wheel and raise the vehicle. Support the front of the vehicle securely on axle stands (see Jacking and vehicle support). Remove the right-handfront road wheel. 3 Remove the auxiliary drivebelt(s) as described in Chapter 1. To improve access, out and the smooth side is next to the belt. 11 If you plan to re-use the timing belt, apply match marks on the sprocket and belt and an arrow... [читать подробенее]


  • - Removal

    40 Remove the distributor (see Chapter 5B). Remove the timing belt and camshaft sprocket (see Sections 5 and 9). 41 Measure the camshaft thrust clearance (endfloat) with a dial indicator (see illustration).If the clearance is greater thanthe service limit, renew the camshaft and/or the cylinder head. 42 Position the knock pin in the exhaust camshaft just above the top of the cylinder head (see illustration). This will position the intake camshaft lobes so the camshaft will be pushed up... [читать подробенее]


  • - Removal

    B . . . then release the clips and disconnect the heater hoses from the bulkhead stubs To prevent accidental deployment (and possible injury),turn the ignition key to LOCK and disconnect the negative battery cable whenever working near airbag components. After the battery is disconnected, wait at least two minutes before beginning work Refitting 6 Refitting is the reverse of removal. Check for proper operation. 10 Heater matrix -removal and refitting ... [читать подробенее]


  • - Removal

    C On VVT-i engines, the oil pressure switch is above the oil filter location Align the flats on the crankshaft with the flats on the pump rotor Engine in-car repair procedures 2A•21 14.2a On 1.3 litre Non-VVT-i engines, the 14.2b On 1.6 litre Non-VVT-i engines, the oil pressure switch is located at the left- oil pressure switch is at the right-hand end hand end of the cylinder block (arrowed) of the cylinder block (arrowed) ... [читать подробенее]


  • - Removal

    A Remove the two screws in the heater knob recesses (arrowed)... 11 Heater and air conditioning control assembly-removal and refitting 1 Remove the rear section of the centre console (see Chapter 11). 2 Pull off the control knobs, and the air recirculation knob. 3 Undo the two screws in the knob recesses, the carefully pull away the centre cluster finish panel. Disconnect the wiring plugs as the panel is removed (see illustrations). 4 Pull up the driver's... [читать подробенее]


  • - Removal

    A Carefully lever the oil sump away from the block Remove the front bolts of the chassis brace (arrowed) Cylinder head bolts tightening sequence - VVT-i engines All engines VVT-i engines 27 Install the cylinder head bolts and washers, then tighten them in sequence to the Stage 1 torque setting (see illustration). 28 Angle tighten the bolts a further 90° in sequence. 29 Check and adjust the valve clearances as necessary (see... [читать подробенее]


  • - Removal

    Undo the two bolts (arrowed) and remove the hose bracket 19 Road test the vehicle and check for proper operation of all accessories. 14 Exhaust manifold -removal and refitting Warning: The engine must he completely cool before beginning this procedure. 1 Remove the upper heat shield from the manifold (see illustration). Note: There may also be a lower heat shield, but this is attached to the manifold from underneath and does not need to be removed. 2 Apply... [читать подробенее]


  • - Removal

    Litre 4E-FE engine Camshafts and followers Carefully prise the oil seal out with a screwdriver engine mounting and the socket to press the seal in (see illustration). 6 Refit the camshaft sprocket and timing belt (see Section 5). Refer to Section 4 and refit the cylinder head cover. 7 Run the engine and check for oil leaks at the camshaft seal. - removal, inspection and refitting Note:Before beginning this procedure, obtaintwo 6x1.0... [читать подробенее]


  • - Semi-detached, estate-agent, terraced, condition, builder, detached, removal, surveyor, spacious, cramped, architect

    For at in on of into with She wanted a place ………….her own. He’ll move ………….tomorrow. He’ll move………….his new flat tomorrow. I share the kitchen…………three other people. The landlord asked the tenant…………. more rent. My flat is ………….the top floor. My flat is………….a modern block. The house is …………good condition. I looked ………….advertisements………….the newspaper. She pays a rent……..£90 a... [читать подробенее]