Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.


Высокие технологии Renewal
просмотров - 173


Throttle body

A Throttle body mounting bolts (arrowed) - Non-VVT-i engines

garage where a natural gas-type appliance (such as a water heater or a clothes dryer) with a pilot light is present Since petrol is carcinogenic, wear latex gloves when there's a possibility of being exposed to fuel, and, if you spill any fuel on your skin, rinse it off immediately with soap and water. Mop up any spills immediately and do not store fuel-soaked rags where they could ignite. The fuel system is under constant pressure, so, if any fuel pipes are to be disconnected, the fuel pressure in the system must be relieved first. When you perform any kind of work on the fuel system, wear safety glasses and have a Class B type fire extinguisher on hand.

1 Verify that the throttle linkage operates smoothly.

2 Start the engine, detach each vacuum hose and, using a vacuum gauge, check there is no vacuum at idle, but that there is vacuum at all other times.

Warning: Wait until the engine is completely cool before beginning this procedure.

3 Drain the cooling system (see Chapter 1).

4 Loosen the hose clamps and remove the air intake duct, then undo the nuts, prise out the two rear fasteners, and remove the plastic cover from the top of the engine (where fitted).

Читайте также

  • - Renewal - VVT-i engines

    Testing - VVT-i engines The vacuum sensor is located on the engine compartment bulkhead Litre 4E-FE ermine farrowed) A Intake air temperature sensor Renewal - Non-VVT-i engines Testing - Non-VVT-i engines Vacuum (MAP) sensor Renewal - Non-VVT-i engines Testing - Non-VVT-i engines 57 Remove the sensor as described below. 58 Connect the leads of an ohmmeter to the terminals of the sensor, and suspend the sensor in a... [читать подробенее]

  • - Renewal - VVT-i engines

    Camshaft position sensor Refitting Crankshaft position sensor wiring plug (arrowed) of the sensor. Compare the readings obtained with those given in the Specifications at the 78 Refitting is a reversal of removal. Note: If a new module has been fitted, it may be necessary to be recode it using special test equipment. Entrust this task to a Toyota dealer or suitably-equipped specialist. After reconnecting the battery, the vehicle must be driven for several km so... [читать подробенее]

  • - Renewal - VVT-i engines

    Testing - VVT-i engines Renewal - 1.3 litre 4E-FE engines Testing - 1.3 litre 4E-FE engines 85 Disconnect the wiring plug from the sensor, and connect the leads of an ohmmeter to the sensor terminals. 86 Measure the resistance of the sensor and compare the readings obtained with those given in the Specifications at the start of this Chapter. 87 Disconnect the sensor wiring plug, and unclip it from the bracket adjacent to the oil level dipstick (see illustration). ... [читать подробенее]

  • - Renewal

    Check B . . . until the outer edge of the seal is flush with the engine block 2 During the check, the engine must be raised slightly to remove the weight from the mountings. 3 Raise the vehicle and support it securely on axle stands (see Jacking and vehicle support), then position a jack under the engine oil sump. Place a large wood block between the jack head and the oil sump, then carefully raise the engine just enough to take the weight off the mountings. Do... [читать подробенее]

  • - Renewal

    When attaching a section of rubber hose to a metal fuel line, be sure to overlap the hose as shown 5 If you must renew any damaged sections, use original equipment hoses or pipes constructed from exactly the same material as the section you are renewing. Do not install substitutes constructed from inferior or inappropriate material or you could cause a fuel leak or a fire. 6 Always, before detaching or disassembling any part of the fuel line system, note the routing of all... [читать подробенее]

  • - Renewal

    Testing Removal Testing Blower motor and resistor - removal and refitting 1 The blower unit is located in the passenger compartment above the left-hand front footwell. If the blower doesn't work, check the fuse and all connections in the circuit for looseness and corrosion. Make sure the battery is fully-charged. 2 Remove the glovebox (see Chapter 11, Section 27). 3 Disconnect the electrical connector from the blower motor resistor. Remove... [читать подробенее]

  • - Fuel filter renewal

    B Slacken the fitting at the bottom of the filter (viewed through the wheel arch) A Using a second spanner, remove the banjo bolt at the top of the fuel filter 8 Make sure the engine idles smoothly, and that there is no hesitation when accelerating. 9 Check that the clutch action is smooth and progressive, that the drive is taken up smoothly, and that the pedal travel is not excessive. Also listen for any noises when the clutch pedal is depressed. 10 Check... [читать подробенее]

  • - Supply, Renewal and Use of Water Resources

    Lesson 2 Упражнение 1. Прочитайте слова и словосочетания и попробуйте догадаться, о чем пойдет речь в следующем тексте: Water supply, fresh water, human use, usable supply, natural purification, groundwater, surface water, precipitation, runoff. Упражнение 2. Прочитайте и переведите текст: Worldwide Supply and Renewal. The world's fixed supply of water... [читать подробенее]

  • - Supply, Renewal and Use of Water Resources

    Worldwide Supply and Renewal. The world's fixed supply of water in all forms (vapor, liquid, and solid) is enormous. If we could distribute it equally, there would be enough to provide every person on earth with 292 trillion liters (77 trillion gallons). However, only about 0.003% of the world's water supply is avail­able as fresh water for human use, and this supply is unevenly distributed. About 97% of the earth's total supply of water is found in the oceans and is too salty for drinking,... [читать подробенее]