Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Charging System
просмотров - 297

ELECTRICAL SYSTEM 16-25

• Remove the rollers [A], springs [B], and spring caps [C] from the starter clutch [D].

• Holding the rotor [A] steady, remove the Allen bolts [B] to separate the rotor and starter clutch [C].

Starter Clutch Sprocket Removal

• Remove:

Alternator cover (see Alternator Rotor/Starter Clutch Re­moval)

Alternator rotor with Starter Clutch (see Alternator Ro­tor/Starter Clutch Removal)

• Remove the woodruff key [A] and spacer [B].

• Remove the starter chain guide [C].

• Remove the starter clutch sprocket [D], starter motor sprocket [E] and starter chain [F] as a set.

• In case that the starter motor has been removed, do the following:

ОRemove the starter motor sprocket. ORemove the alternator rotor with the starter clutch, starter clutch sprocket and starter chain as a set.

Starter Clutch Sprocket Installation

• Apply a thin coat of molybdenum disulfide grease to the frictional surface between the crankshaft and the starter clutch sprocket.

• If the starter motor has been removed, install it first.

• Install the starter clutch sprocket, starter motor sprocket and starter chain as a set.

• Install the alternator rotor with the starter clutch and alter­nator cover.

Torque -Alternator Rotor Bolt: 69 N-m (7.0 kgf-m, 51 ft-lb) Alternator Cover Bolt: 11 N-m (1.1 kgf-m, 95 in-lb)


Читайте также


  • - CHARGING SYSTEM ELEC

    L-9 CHARGING SYSTEM ELEC + + 3. Charging voltage • Connect the engine tachometer to the spark plug lead Ø • Connect the pocket tester (DC20 V) to the battery. Tester (+) lead—( Battery (+) terminalØ Tester (-) lead—( Battery (-) terminalØ • Measure the battery terminal voltage • Start the engine and accelerate to about 5,000 rpm • Check the terminal voltage Charging voltage = Measured... [читать подробенее]


  • - ELECTRICAL SYSTEM 16-27 Charging System

    NOTE ОTo keep the loss of engine oil to a minimum, set the motorcycle vertically. • Remove the alternator cover (see Alternator Rotor and Starter Clutch Removal). • Remove the screws [A] and the holding plate [B] for the stator wiring. • Unscrew the Allen bolts [C] and remove the stator [D]. Remove the grommet for the crankshaft sensor lead. Alternator Stator Installation • Apply silicone sealant [A] around the circumference of the wiring grommets... [читать подробенее]


  • - Charging System

    ELECTRICAL SYSTEM 16-31 Regulator Circuit Check NOTE Rectifier Circuit Inspection Charging System ELECTRICAL SYSTEM Rectifier circuit check • Remove the left side cover (see Side Cover Removal in the Frame chapter). Disconnect the regulator/rectifier lead connector [A]. Brown Lead Terminal [A] White/Red Lead Terminal [B] Black Lead Terminal [C] Yellow 1 Lead Terminal [D] Yellow 2 Lead Terminal [E] Yellow 3 Lead Terminal [F] • Connect the... [читать подробенее]


  • - Charging System

    ELECTRICAL SYSTEM 16-25 • Remove the rollers [A], springs [B], and spring caps [C] from the starter clutch [D]. • Holding the rotor [A] steady, remove the Allen bolts [B] to separate the rotor and starter clutch [C]. Starter Clutch Sprocket Removal • Remove: Alternator cover (see Alternator Rotor/Starter Clutch Re­moval) Alternator rotor with Starter Clutch (see Alternator Ro­tor/Starter Clutch Removal) • Remove the woodruff key [A]... [читать подробенее]


  • - Charging System

    ELECTRICAL SYSTEM Alternator Rotor/Starter Clutch Installation • Apply a non-permanent locking agent to the threads of the starter clutch Allen bolts, and tighten them to the specified torque in assembling the starter clutch onto the alternator rotor. Torque -Starter Clutch Allen Bolts: 34 N-m (3.5 kgf-m, 25 ft-lb) OBe careful that the rollers do not drop out of the starter clutch during assembly. • Using a high flash-point solvent, clean off any oil or dirt that may... [читать подробенее]


  • - Charging System

    ELECTRICAL SYSTEM 16-29 • Check that the ignition switch is turned off, and connect the hand tester [A] as shown in the table. Special Tool - Hand Tester:57001-1394 • Start the engine, and note the voltage readings at vari­ ous engine speeds with the headlight turned on and then turned off. The readings should show nearly battery volt­ age when the engine speed is low, and, as the engine speed rises, the readings should also rise. But they must be kept under the... [читать подробенее]