Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Coolant
просмотров - 301

COOLING SYSTEM

COOLING SYSTEM 4-7

 
 

Coolant Deterioration Inspection

• Visually inspect the coolant in the reservoir tank.

OIf whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded. If the coolant is brown, iron or steel parts are rusting. In either case flush the cooling system.

OIf the coolant gives off an abnormal smell, check for a cooling system leak. It may be caused by exhaust gas leaking into the cooling system.

Coolant Level Inspection

• Referto the Coolant Level Inspection in the Periodic Main­ tenance chapter.

Coolant Draining

• Referto the Coolant Change in the Periodic Maintenance chapter.

Coolant Filling

• Referto the Coolant Change in the Periodic Maintenance chapter.

Visual Leak Inspection Any time the system slowly loses water, inspect for leaks.

• Check the water pump body drainage outlet passage [A] for coolant leaks.

• If the mechanical seal is damaged, the coolant leaks through the seal and drains through the passage. Re­place the mechanical seal.

• If there are no apparent leaks, pressure test the system.

Cooling System Pressure Testing


Читайте также


  • - Undo the 6 bolts (arrowed) and remove the coolant pump

    Undo the nut and bolt (arrowed) and remove the auxiliary belt tensioner assembly There is no need to disconnect the fluid pipes from the pump, suspend it from the front panel/ cowling using cable ties/wire. 5 Set the engine to TDC on No 1 cylinder as described in Section 3. 6 To prevent the crankshaft from rotating whilst the crankshaft pulley central bolt is slackened, engage top gear and have an assistant press the brake pedal firmly. Slacken the pulley bolt. On... [читать подробенее]


  • - Disconnect the coolant temperature gauge sender wiring plug (arrowed)

    A Remove the two nuts (smaller arrows) retaining the coolant neck to the cylinder head, then remove the top bolt (larger arrow) from the coolant pump Use a screwdriver to lever the wiring clip from the dipstick tube bracket Undo the radiator upper retaining bracket bolts (arrowed) 3•6 Cooling, heating and air conditioning systems on the coolant pump by looking through the space behind the pulley just below the coolant pump shaft. 4... [читать подробенее]


  • - B Engine coolant temperature sender (arrowed) - VVT-i engine

    Renew the coolant pump O-ring 8.7a Engine coolant temperature sender The bolts marked (A) are 30 mm long whilst the ones marked (B) are 35 mm long Small arrows indicate the pump-to-block bolts. Larger arrows show weep holes A-FE engine E-FE engine Refitting ZZ-FE and 3ZZ-FE engines 13 Drain the engine coolant as described in Chapter 1. 14 Remove the auxiliary drivebelt as described in Chapter 1. 15 Undo the 6 bolts, and... [читать подробенее]


  • - CLEANING THE CRANKCASE FILTER AND CHECKING THE COOLANT LEVEL

    Never operate the engine without the air filter ele- ment installed. Unfiltered air will cause rapid wear of engine parts and may damage the engine. Ope- rating the engine without the filter element will also affect the carburettor tuning, leading to poor engine performance and possibly overheating. 5. Install • Air filter element • Air filter case cover 7 Nm (0,7 m•kg) CLEANING THE CRANKCASE FILTER 1. Remove • Crankcase filter cover Ø 2• Filter cover... [читать подробенее]


  • - COOLING SYSTEM 4-9 Coolant

    NOTE CAUTION During pressure testing, do not exceed the pres­sure for which the system is designed. The maxi­mum pressure is 123 kPa (1.25 kgf/cm², 18 psi). • Remove the left lower fairing (see Lower Fairing Removal in the Frame chapter). • Remove the radiator cap, and install a cooling system pressure tester [A] on the radiator filler neck.О Wet the cap sealing surfaces with water or coolant to prevent pressure leaks. • Build up pressure in the system... [читать подробенее]


  • - Coolant Flow Chart

    COOLING SYSTEM Permanent type antifreeze is used as a coolant to protect the cooling system from rust and corrosion. When the engine starts, the water pump turns and the coolant circulates. The thermostat is a wax pellet type which opens or closes with coolant temperature changes. The thermostat continuously changes its valve opening to keep the coolant temperature at the proper level. When coolant temperature is below 80.5 &... [читать подробенее]


  • - Coolant

    COOLING SYSTEM COOLING SYSTEM 4-7     Coolant Deterioration Inspection • Visually inspect the coolant in the reservoir tank. OIf whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded. If the coolant is brown, iron or steel parts are rusting. In either case flush the cooling system. OIf the coolant gives off an abnormal smell, check for a cooling system leak. It may be caused by exhaust gas leaking into... [читать подробенее]