Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Front Fork
просмотров - 174

SUSPENSION 13-11

Front Fork Assembly

• Replace the following parts with new ones after removal.

Dust Seal [A]

Retaining Ring [B]

Oil Seal [C]

Inner Guide Bushing [D]

Outer Guide Bushing [E]

Bottom Allen Bolt Gasket [F]

• Put the cylinder unit [A] with the spring into the inner tube [B] protruding from the inner tube, and install the cylinder base [C] onto the bottom end of the cylinder unit.

○Install the cylinder base with the tapered end [D] up.

• Install the inner tube, cylinder unit, and cylinder base as a set into the outer tube.

       
pn \      
®- \    
  О  
   
   
GM040311S1 С

• Install the new guide bushing [A] with a used guide bush­ing [B] on it by tapping the used guide bushing with the fork oil seal driver [C] until it stops.

○The split [D] of the bushing should face toward the side of the vehicle.

Special Tool - Front Fork Oil Seal Driver: 57001-1219

• Apply grease to the oil seal lips and install the washer and the oil seal [A] into the outer tube.

Special Tool - Front Fork Oil Seal Driver: 57001-1219 [B]

• Install:

Retaining Ring Dust Seal

• Hold the front fork horizontally in a vise [A].

• Apply a non-permanent locking agent to the threads of the Allen bolt and screw the Allen bolt into the bottom of the outer tube.

• Hold the cylinder unit [B] with the special tools and tighten the Allen bolt [C].

Special Tools-Fork Cylinder Holder Handle: 57001-183 [D] Fork Cylinder Holder Adapter: 57001-1057 [E]

Torque - Bottom Allen Bolt: 30 N-m (3.1 kgf-m, 22 ft-lb)


Читайте также


  • - FRONT FORK CHAS

    Mm Never reuse the oil seal. FRONT FORK CHAS J-15 Stand the scooter on a level surface Stand the scooter on its centre stand Securely support the scooter so there is no dan- ger of it falling over. FRONT FORK REMOVAL s WARNING: 1. Loosen: 1• Bolts (lower shank) Ø 2. Extract: • Retaining clip • Cap bolt Ø FRONT FORK DISASSEMBLY 1. Remove: • Cap • Spring • Bolt... [читать подробенее]


  • - FRONT FORK CHAS

    J-16 7. Inspect: • Inner tube operation Un-smooth operation —( Disassemble and recheck 3. Install: • Plain washer Ø NEW • Bolt (damper rod) Ø 4. Tighten: • Bolt (damper rod) Ø 23 Nm (2.3 m•kg) 8. Fill: •   Oil quantity 0.130L Recommended oil: Fork oil SAE 20 or equivalent. Fork oil NOTE: Tighten damper rod bolt Ø while holding the damper rod with a T... [читать подробенее]


  • - FRONT FORK CHAS

    J-14 FRONT FORK CHAS   Order   Job name/Part name   Quantity   Remarks   Front fork assembly   Remove the parts in order Cap/circlip Refer to “FRONT FORK REMOVAL/ O-ring INSTALLATION” section Fork spring Refer to “FRONT FORK ASSEMBLY” Dust seal section Retaining clip   Oil seal ... [читать подробенее]


  • - Front Fork

    SUSPENSION 13-11 Front Fork Assembly • Replace the following parts with new ones after removal. Dust Seal [A] Retaining Ring [B] Oil Seal [C] Inner Guide Bushing [D] Outer Guide Bushing [E] Bottom Allen Bolt Gasket [F] • Put the cylinder unit [A] with the spring into the inner tube [B] protruding from the inner tube, and install the cylinder base [C] onto the bottom end of the cylinder unit. &... [читать подробенее]


  • - Front Fork

    Front Fork Disassembly • Remove the front fork (see Front Fork Removal). •&... [читать подробенее]


  • - Front Fork

    SUSPENSION 13-11 Front Fork Assembly • Replace the following parts with new ones after removal. Dust Seal [A] Retaining Ring [B] Oil Seal [C] Inner Guide Bushing [D] Outer Guide Bushing [E] Bottom Allen Bolt Gasket [F] • Put the cylinder unit [A] with the spring into the inner tube [B] protruding from the inner tube, and install the cylinder base [C] onto the bottom end of the cylinder unit. &... [читать подробенее]


  • - Front Fork

    Front Fork Disassembly • Remove the front fork (see Front Fork Removal). •&... [читать подробенее]