Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство ENGINE TOP END 5-19
просмотров - 234

NOTE

Camshaft, Camshaft Chain

ENGINE TOP END

CAUTION

The camshaft caps are machined with the cylinder head. So, if a cap is installed in a wrong location, the camshaft may seize because of improper oil clearance in the bearings.

CAUTION

• First tighten down the two camshaft cap bolts (#1 and #2 bolts in the figure) evenly to seat the camshafts in place, then tighten all bolts following the specified tightening se­ quence.

Torque - Camshaft Cap Bolts: 12 N·m (1.2 kgf·m, 8.5 ft·lb)

• Install the head oil pipes.

Torque -Oil Pipe Bolts: 11 N·m (1.1 kgf·m, 95 in·lb)

• Install the camshaft chain tensioner (see Camshaft Chain Tensioner Installation).

• Check the chain timing.

Camshaft and Sprocket Assembly

OThe inlet and exhaust sprockets are identical.

• Install the sprockets so that the marked [A] ("IN" and "EX") side faces to the left side.

Inlet sprocket must use "l" marked bolt holes. Exhaust sprocket must use "E" marked bolt holes.

• Apply a non-permanent locking agent to the camshaft sprocket bolts and tighten them.

Torque - Camshaft Sprocket Bolts: 15 N·m (1.5 kgf·m, 11.0 ft·lb)

If a new camshaft is to be used, apply a thin coat of a molybdenum disulfide oil to the cam surfaces.

Camshaft, Camshaft Cap Wear

The journal wear is measured using plastigage (press gauge), which is inserted into the clearance to be mea­sured. The plastigage indicates the clearance by the amount it is compressed and widened when the parts are assembled.

• Cut strips of plastigage to journal width. Place a strip on each journal parallel to the camshaft with the camshaft in­stalled in the correct position and so that the plastigage will be compressed between the journal and camshaft cap.

• Install the camshaft caps, tightening the bolts in the cor­rect sequence.

Torque -Camshaft Cap Bolts: 12 N-m (1.2 kgf-m, 8.5ft-lb)

ODo not turn the camshaft when the plastigage is be­tween the journal and camshaft cap.

• Remove the camshaft caps again, and measure the plas-tigage width [A] to determine the clearance between each journal and camshaft cap. Measure the widest portion of the plastigage. Plastigage Scale [B]

• If any clearance exceeds the service limit, measure the camshaft journal diameter and the camshaft bearing in­side diameter.

• If any of the measurements is beyond the service limit, replace the worn part and check the clearance again.

Camshaft Journal, Camshaft Cap Clearance Standard: 0.030 ~ 0.071 mm (0.0012 ~ 0.0028 in.)

Service Limit: 0.16 mm (0.006 in.)

Camshaft Chain Guide Wear

• Visually inspect the rubber [A] on the guides.

• If the rubber is damaged or cut, replace the guides.


Читайте также


  • - ENGINE TOP END 5-35 Cylinder, Piston

    Piston Diameter • Measure the outside diameter [A] of each piston 5 mm [B] up from the bottom of the piston at a right angle to the direction of the piston pin. • If the measurement is under the service limit, replace the piston. Piston Diameter Standard: 73.942 ~ 73.957 mm (2.9111 ~ 2.9117 in.) Service Limit: 73.79 mm (2.9051 in.) Boring, Honing When boring and honing a cylinder, note the following: OThere is one oversize piston available. Oversize pistons require... [читать подробенее]


  • - ENGINE TOP END 5-19

    NOTE Camshaft, Camshaft Chain ENGINE TOP END CAUTION The camshaft caps are machined with the cylinder head. So, if a cap is installed in a wrong location, the camshaft may seize because of improper oil clearance in the bearings. CAUTION • First tighten down the two camshaft cap bolts (... [читать подробенее]


  • - ENGINE TOP END 5-13

    NOTE Clean Air System ENGINE TOP END Vacuum Switch Valve Test Using the vacuum gauge and a syringe, inspect the vac­uum switch operation as follows. • Remove a vacuum switch valve. • Connect a vacuum gauge [A] and syringe [B] or fork oil level gauge to the vacuum hoses as shown. Air Flow [C] Special Tool - Fork Oil Level Gauge: 57001-1290 • Gradually raise the vacuum (lower the pressure) applied to the vacuum switch valve, and check the valve opera­ tion.... [читать подробенее]


  • - ENGINE TOP END

    Valves ENGINE TOP END 5-25 Valve Clearance Inspection • Refer to the Valve Clearance Inspection in the Periodic Maintenance chapter. Valve Removal • Remove the cylinder head (see Cylinder Head Removal). • Use a valve spring compressor assembly to press down the valve spring retainer, and remove the split keepers. Special Tools -Valve Spring Compressor Assembly: 57001 -241 [A] Valve Spring Compressor Adapter, ф22: 57001-1202 [B] Valve... [читать подробенее]


  • - ENGINE TOP END 5-35 Cylinder, Piston

    Piston Diameter • Measure the outside diameter [A] of each piston 5 mm [B] up from the bottom of the piston at a right angle to the direction of the piston pin. • If the measurement is under the service limit, replace the piston. Piston Diameter Standard: 73.942 ~ 73.957 mm (2.9111 ~ 2.9117 in.) Service Limit: 73.79 mm (2.9051 in.) Boring, Honing When boring and honing a cylinder, note the following: OThere is one oversize piston available. Oversize pistons require... [читать подробенее]


  • - ENGINE TOP END 5-19

    NOTE Camshaft, Camshaft Chain ENGINE TOP END CAUTION The camshaft caps are machined with the cylinder head. So, if a cap is installed in a wrong location, the camshaft may seize because of improper oil clearance in the bearings. CAUTION • First tighten down the two camshaft cap bolts (... [читать подробенее]


  • - ENGINE TOP END 5-13

    NOTE Clean Air System ENGINE TOP END Vacuum Switch Valve Test Using the vacuum gauge and a syringe, inspect the vac­uum switch operation as follows. • Remove a vacuum switch valve. • Connect a vacuum gauge [A] and syringe [B] or fork oil level gauge to the vacuum hoses as shown. Air Flow [C] Special Tool - Fork Oil Level Gauge: 57001-1290 • Gradually raise the vacuum (lower the pressure) applied to the vacuum switch valve, and check the valve opera­ tion.... [читать подробенее]


  • - ENGINE TOP END

    Valves ENGINE TOP END 5-25 Valve Clearance Inspection • Refer to the Valve Clearance Inspection in the Periodic Maintenance chapter. Valve Removal • Remove the cylinder head (see Cylinder Head Removal). • Use a valve spring compressor assembly to press down the valve spring retainer, and remove the split keepers. Special Tools -Valve Spring Compressor Assembly: 57001 -241 [A] Valve Spring Compressor Adapter, ф22: 57001-1202 [B] Valve... [читать подробенее]