Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Front Fork
просмотров - 226

Front Fork Disassembly

• Remove the front fork (see Front Fork Removal).

DThraeinfotlhloewfionrgk poailr(tsseaereFrroenmt oFvoerdk dOuilriCnghadnrgaein)i.ng the fork

oil.

Top Bolt and O-ring Spacer

Fork Spring Seat Fork Spring

• Hold the front fork horizontally in a vise [A].

• Stop the cylinder unit [B] from turning by using the special tools.

• Unscrew the Allen bolt [C], and take the gasket out of the bottom of the outer tube.

Special Tools - Fork Cylinder Holder Handle: 57001-183 [D] Fork Cylinder Holder Adapter: 57001-1057 [E]

• Takethecylinderunitoutoftheinnertube.

SReepmaoraveteththeedinunstesr etuabl e[Af]rofrmomthteheouotuetretrutbuebsea. s follows: ○Remove the retaining ring [B] from the outer tube.

○Use the fork outer tube weight [A] to separate the outer tube [B] from the inner tube [C] Holding the inner tube by hand, pull the outer tube several times to pull out the inner tube.

Special Tool - Fork Outer Tube Weight: 57001-1218

○Take out the cylinder base out of the outer tube.

• Remove the guide bushings [A], outer tube guide bushing [B], washer [C], and oil seal [D] from the inner tube.


Читайте также


  • - FRONT FORK CHAS

    Mm Never reuse the oil seal. FRONT FORK CHAS J-15 Stand the scooter on a level surface Stand the scooter on its centre stand Securely support the scooter so there is no dan- ger of it falling over. FRONT FORK REMOVAL s WARNING: 1. Loosen: 1• Bolts (lower shank) Ø 2. Extract: • Retaining clip • Cap bolt Ø FRONT FORK DISASSEMBLY 1. Remove: • Cap • Spring • Bolt... [читать подробенее]


  • - FRONT FORK CHAS

    J-16 7. Inspect: • Inner tube operation Un-smooth operation —( Disassemble and recheck 3. Install: • Plain washer Ø NEW • Bolt (damper rod) Ø 4. Tighten: • Bolt (damper rod) Ø 23 Nm (2.3 m•kg) 8. Fill: •   Oil quantity 0.130L Recommended oil: Fork oil SAE 20 or equivalent. Fork oil NOTE: Tighten damper rod bolt Ø while holding the damper rod with a T... [читать подробенее]


  • - FRONT FORK CHAS

    J-14 FRONT FORK CHAS   Order   Job name/Part name   Quantity   Remarks   Front fork assembly   Remove the parts in order Cap/circlip Refer to “FRONT FORK REMOVAL/ O-ring INSTALLATION” section Fork spring Refer to “FRONT FORK ASSEMBLY” Dust seal section Retaining clip   Oil seal ... [читать подробенее]


  • - Front Fork

    SUSPENSION 13-11 Front Fork Assembly • Replace the following parts with new ones after removal. Dust Seal [A] Retaining Ring [B] Oil Seal [C] Inner Guide Bushing [D] Outer Guide Bushing [E] Bottom Allen Bolt Gasket [F] • Put the cylinder unit [A] with the spring into the inner tube [B] protruding from the inner tube, and install the cylinder base [C] onto the bottom end of the cylinder unit. &... [читать подробенее]


  • - Front Fork

    Front Fork Disassembly • Remove the front fork (see Front Fork Removal). •&... [читать подробенее]


  • - Front Fork

    SUSPENSION 13-11 Front Fork Assembly • Replace the following parts with new ones after removal. Dust Seal [A] Retaining Ring [B] Oil Seal [C] Inner Guide Bushing [D] Outer Guide Bushing [E] Bottom Allen Bolt Gasket [F] • Put the cylinder unit [A] with the spring into the inner tube [B] protruding from the inner tube, and install the cylinder base [C] onto the bottom end of the cylinder unit. &... [читать подробенее]


  • - Front Fork

    Front Fork Disassembly • Remove the front fork (see Front Fork Removal). •&... [читать подробенее]