Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Maintenance Procedure
просмотров - 99

NOTE

Headlight Beam Vertical Adjustment

Headlight Beam Horizontal Adjustment

• Insert the conventional screwdriver into the adjuster from underside of the headlight, turn the horizontal adjuster [A] on the headlight housing in or out until the beam points straight ahead. Turning the adjuster clockwise moves the headlight beam to the left.

• Insert the conventional screwdriver into the adjuster from the slit of the meter cover, turn the vertical adjuster [B] on the headlight housing in or out to adjust the headlight vertically.

○On high beam, the brightest point should be slightly be­low horizontal with the motorcycle on its wheels and rider seated. Adjust the headlight to the proper angle according to local regulations.

Side Stand Switch Operation Inspection

• Inspect the side stand switch [A] operation in accordance to below table.

Sidestand Switch Operation

Side Stand Gear Position Clutch Lever Engine Start Engine Run
Up Neutral Released Starts Continue running
Up Neutral Pulled in Starts Continue running
Up In Gear Released Doesn’t start Continue running
Up In Gear Pulled in Starts Continue running
Down Neutral Released Starts Continue running
Down Neutral Pulled in Starts Continue running
Down In Gear Released Doesn’t start Stops
Down In Gear Pulled in Doesn’t start Stops

If the side stand switch operation does not work, inspect or replace the following item. Battery (see Battery Activation in the Electrical System chapter)

Main Fuse 30 A (see Fuses in the Electrical System chapter)

Ignition Fuse 10 A (see Fuses in the Electrical System chapter)

Ignition Switch (see Switch Inspection in the Electrical System chapter)

Side Stand Switch (see Switch Inspection in the Electri­cal System chapter)

2-38Периодический ремонт

Engine Stop Switch (see Switch Inspection in the Elec­trical System chapter)

Starter Button (see Switch Inspection in the Electrical System chapter)

Starter Relay (see Starter Relay Inspection in the Elec­trical System chapter)

Junction Box (see Junction Box Inspection in the Elec­trical System chapter)

Harness (see Wiring Inspection in Electrical System chapter)

If the all parts are good condition, replace the IC igniter.

Engine Stop Switch Operation Inspection


Читайте также


  • - Maintenance Procedure

    NOTE L (When engine is completely dry) L (When filter is removed) Engine Oil Grade: API SE, SF, SG or API SH or SJ with JASO MA Viscosity: SAE 10W40 Capacity: 2.8 L (When filter is not removed)&... [читать подробенее]


  • - Maintenance Procedure

    NOTE &... [читать подробенее]


  • - Maintenance Procedure

    NOTE Total Amount 1.7 L (1.8 US qt) Maintenance Procedure CAUTION NOTE Coolant Filling • Install the drain plug [A]. Always replace the gasket with a new one. • Tighten the drain plug. Torque -Coolant Drain Plug: 11 N·m (1.1 kgf·m, 95 in·lb) • Fill [A] the radiator up to the bottom of the radiator filler neck [B] with coolant [C], and install the cap turning it clockwise about 1/4 turn.&... [читать подробенее]


  • - Maintenance Procedure

    Fourth Step • Set the dimmer switch [A] to low beam position. • Start the engine. • The low beam headlight and license plate light should go on. • If the low beam headlight and license plate light do not go on, inspect or replace the following item. Headlight Low Beam Bulb (see Lighting System in the Electrical System chapter) License Plate Light Bulb Headlight Fuse 10 A (see Fuses in the Electrical System chapter) Dimmer Switch (see Switch Inspection in the... [читать подробенее]


  • - Maintenance Procedure

    Third Step Second Step • Turn the ignition switch to P (Park) position. • The city light and taillight should go on. • If the light does not go on, inspect or replace the following item. Ignition Switch (see Switch Inspection in the Electrical System chapter)• Turn on the turn signal switch [A] (left or right position). • The left or right turn signal lights [B] (front and rear) ac­cording to the switch position should flash. • The turn signal indicator LED [C]... [читать подробенее]


  • - Maintenance Procedure

    NOTE Others Second Step First Step • Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to stop position [A]. • Push the starter button. • The engine does not start. • If the engine starts, inspect or replace the following item. Engine Stop Switch (see Switch Inspection in the Elec­trical System chapter)• Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to run... [читать подробенее]


  • - Maintenance Procedure

    Brakes Complete cleaning and drying the chain within 10 minutes. Any other cleaning solution such as gasoline or trichloroethylene will cause deterioration and swelling of the O-ring. Blow the chain dry with compressed air immedi­ately after cleaning.• Apply oil to the sides of the rollers so that oil will penetrate to the rollers and bushings. Apply the oil to the O-rings so that the O-rings will be coated with oil. • Wipe off any excess oil.Brake Fluid Leak (Brake Hose... [читать подробенее]


  • - Maintenance Procedure

    Suspension Front Forks/Rear Shock Absorber Operation Inspection • Pump the forks down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the forks do not smoothly or noise is found, inspect the fork oil level or fork clamps (see Front Fork Oil Change in the Suspension chapter). Периодический ремонт2-31 • Pump the seat down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the shock absorber does not smoothly stroke or noise... [читать подробенее]


  • - Maintenance Procedure

    Spark Plug Gap Lights and Switches Operation Inspection First Step • Turn on the ignition switch. The following lights should go on according to below table. 0.6 &... [читать подробенее]


  • - Maintenance Procedure

    Steering Play Adjustment NOTE О The cables and wiring will have some effect on the mo­tion of the fork which must be taken into account. Be sure the wires and cables are properly routed. OThe bearings must be in good condition and properly lubricated in order for any test to be valid.•Adjust the steering if necessary. • Remove: Handlebar (see Handlebar Removal in the Steering chapter) Side Cover (see Side Cover Removal in the Frame chap­ter) Seat (see Seat Removal in... [читать подробенее]