Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Ignition System
просмотров - 270

ELECTRICAL SYSTEM

IC Igniter Operation Voltage Check

NOTE

OFollow the instructions in the manufacturer’s operation manual for the proper procedure for operating the ig­niter checker.

OThe igniter checker can perform inspections by simu­lating the following dynamic characteristics: the igniter response in relating to the engine speed, interlock cir­cuit signals, tachometer signals, and engine overspeed limiter signals.

OThe igniter checker cannot be used for inspecting the conditions of the CDI unit.

If the igniter is defective, replace it.

• Remove the seat (see Seat Removal in the Frame chap­ ter).

Disconnect the IC igniter connector [A].

• Set the Hand Tester [A] to the × 25 V DC range, and connect it to the connector come from harness side as follows.

Tester (+) terminal [B] —►BR/W lead Tester (-) terminal [C] —►BK/Y lead

Special Tool - Hand Tester: 57001-1394

Needle Adapter Set: 57001-1457

• Turn the ignition switch on , and read the voltage.

IC Igniter Operation Voltage: Battery Voltage

If the tester reading is not specified one, check the battery voltage, ignition switch and ignition fuse.


Читайте также


  • - IGNITION SYSTEM ELEC

    L-6 IGNITION SYSTEM ELEC + + 4. Ignition coil resistance • Disconnect the ignition coil connector from the wireharness. • Check if the primary coil has the specified resistance • Connect the tester (&... [читать подробенее]


  • - Ignition system

    FAULTY BRAKE TRBL SHTG A-4 TRBL SHTG OVERHEATING OR OVERCOOLING V belt Secondary sliding sheaf V belt Clutch shoes spring Engine oil Clutch Compression system Air cleaner Clogged air cleaner element Worn cylinder Worn or seized piston ring Cylinder head gasket broken Cylinder gasket broken Carbon deposit build-up Improperly adjusted valve clearance Improperly contacted valve and valve seat Faulty... [читать подробенее]


  • - IF THE IGNITION SYSTEM FAILS TO OPERATE. (NO SPARK OR INTERMITTENT SPARK)

    IGNITION SYSTEM ELEC L-5 IGNITION SYSTEM ELEC IGNTION SYSTEM ELEC L-4 SWITCH POSITION AND TERMINAL CONNECTION IGNTION SYSTEM CIRCUIT DIAGRAM 1. Front brake switch 2. Horn switch 3. Lights switch 4. Flashing switch 5. Indicator switch 6. Main switch 7. Front brake switch 8. Starter switch 9. Side stand switch 10. Fuse + O indicates the position of the connector 1. CDI flywheel 2. Ignition unit 3. Ignition... [читать подробенее]


  • - Ignition System

    The ignition system enables the engine to start and keep running. It depends on the type of engine and the fuel used. Petrol engines are typically ignited by a precisely timed spark, and diesel engines by compression heating. The ignition is located either on the side of the steering column or on the dashboard. It is a multifunction switch, into which you insert your key, in order to energize the electrical circuits and activate your starter motor. The spark plugignites the fuel and air... [читать подробенее]


  • - Ignition System

    The ignition system enables the engine to start and keep running. It depends on the type of engine and the fuel used. Petrol engines are typically ignited by a precisely timed spark, and diesel engines by compression heating. The ignition is located either on the side of the steering column or on the dashboard. It is a multifunction switch, into which you insert your key, in order to energize the electrical circuits and activate your starter motor. The spark plugignites the fuel and air... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM 16-39 NOTE Ignition Coil Primary Peak Voltage Inspection Starter Button Operation Check • Remove the seats (see Seat Removal in the Frame chap­ter). • Set the Hand Tester [A] to the × 25 V DC range, connect it to the IC igniter [B] lead as follows. Hand Tester (+) Terminal [C] —&... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM IC Igniter Operation Voltage Check NOTE OFollow the instructions in the manufacturer’s operation manual for the proper procedure for operating the ig­niter checker. OThe igniter checker can perform inspections by simu­lating the following dynamic characteristics: the igniter response in relating to the engine speed, interlock cir­cuit signals, tachometer signals, and engine overspeed limiter signals. OThe igniter checker cannot be used for... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM Ignition System Circuit Ignition System ELECTRICAL SYSTEM 16-33 Charging System Circuit Charging System ELECTRICAL SYSTEM CAUTION Do not apply more than 24 V to the regulator/recti­fier and do not leave the 24 V applied for more than a few seconds, or the unit will be damaged. • If the test light did not light when the 24 V was applied momentarily to the BR terminal, the regulator/rectifier is defective. Replace... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM 16-39 NOTE Ignition Coil Primary Peak Voltage Inspection Starter Button Operation Check • Remove the seats (see Seat Removal in the Frame chap­ter). • Set the Hand Tester [A] to the × 25 V DC range, connect it to the IC igniter [B] lead as follows. Hand Tester (+) Terminal [C] —&... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM IC Igniter Operation Voltage Check NOTE OFollow the instructions in the manufacturer’s operation manual for the proper procedure for operating the ig­niter checker. OThe igniter checker can perform inspections by simu­lating the following dynamic characteristics: the igniter response in relating to the engine speed, interlock cir­cuit signals, tachometer signals, and engine overspeed limiter signals. OThe igniter checker cannot be used for... [читать подробенее]