Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Ignition System
просмотров - 267

ELECTRICAL SYSTEM 16-39

NOTE

Ignition Coil Primary Peak Voltage Inspection

Starter Button Operation Check

• Remove the seats (see Seat Removal in the Frame chap­ter).

• Set the Hand Tester [A] to the × 25 V DC range, connect it to the IC igniter [B] lead as follows.

Hand Tester (+) Terminal [C] —►BK/R Lead Hand Tester (-) Terminal [D] —►Frame Ground

Special Tool - Hand Tester: 57001-1394

Needle Adapter Set: 57001-1457

• Turn the ignition switch on and push the starter button.

• Read the voltage.

Starter Button Voltage: Battery Voltage

If the tester reading is not specified one, replace the IC igniter.

• Remove:

Side Covers (see Side Cover Removal in the Frame

chapter)

Lower Fairings (see Lower Fairing Removal in the Frame

chapter)

• Remove the spark plug caps from the spark plugs.

• Attach a good spark plugs to the removed spark plug caps and ground them to the engine.

ОTo obtain a correct measurement, the wires as well as the wire connections must be correct. Take the volt­age measurement with the proper cylinder compres­sion (with the spark plugs in the cylinder head). Without proper compression, a correct measurement cannot be obtained.

• Set the tester to the DC 250 V range. Connect the peak voltage adapter [B] to the tester [A], and connect the adapter terminals to the respective terminals of the ignition coil [C].

○Keep the terminals connected.

Special Tool - Kawasaki Hand Tester: 57001-1394 Peak Voltage Adapter: 57001-1415 Type: KEK-54-9-B

Connect #1

Adapter’s positive (+) → terminal black wire

terminal [D]

Adapter’s negative (–) → red wire terminal [E] terminal

#2

Adapter’s positive (+) → green wire terminal terminal

Adapter’s negative (–) → red wire terminal terminal

TurntheignitionswitchON.

• Shift the gears to neutral, and run the engine stop switch.

• Turn the starter motor for several seconds and read the maximum value on the tester.

 

Ignition Coil Primary Peak Voltage Standard: DC100 V or more


Читайте также


  • - IGNITION SYSTEM ELEC

    L-6 IGNITION SYSTEM ELEC + + 4. Ignition coil resistance • Disconnect the ignition coil connector from the wireharness. • Check if the primary coil has the specified resistance • Connect the tester (&... [читать подробенее]


  • - Ignition system

    FAULTY BRAKE TRBL SHTG A-4 TRBL SHTG OVERHEATING OR OVERCOOLING V belt Secondary sliding sheaf V belt Clutch shoes spring Engine oil Clutch Compression system Air cleaner Clogged air cleaner element Worn cylinder Worn or seized piston ring Cylinder head gasket broken Cylinder gasket broken Carbon deposit build-up Improperly adjusted valve clearance Improperly contacted valve and valve seat Faulty... [читать подробенее]


  • - IF THE IGNITION SYSTEM FAILS TO OPERATE. (NO SPARK OR INTERMITTENT SPARK)

    IGNITION SYSTEM ELEC L-5 IGNITION SYSTEM ELEC IGNTION SYSTEM ELEC L-4 SWITCH POSITION AND TERMINAL CONNECTION IGNTION SYSTEM CIRCUIT DIAGRAM 1. Front brake switch 2. Horn switch 3. Lights switch 4. Flashing switch 5. Indicator switch 6. Main switch 7. Front brake switch 8. Starter switch 9. Side stand switch 10. Fuse + O indicates the position of the connector 1. CDI flywheel 2. Ignition unit 3. Ignition... [читать подробенее]


  • - Ignition System

    The ignition system enables the engine to start and keep running. It depends on the type of engine and the fuel used. Petrol engines are typically ignited by a precisely timed spark, and diesel engines by compression heating. The ignition is located either on the side of the steering column or on the dashboard. It is a multifunction switch, into which you insert your key, in order to energize the electrical circuits and activate your starter motor. The spark plugignites the fuel and air... [читать подробенее]


  • - Ignition System

    The ignition system enables the engine to start and keep running. It depends on the type of engine and the fuel used. Petrol engines are typically ignited by a precisely timed spark, and diesel engines by compression heating. The ignition is located either on the side of the steering column or on the dashboard. It is a multifunction switch, into which you insert your key, in order to energize the electrical circuits and activate your starter motor. The spark plugignites the fuel and air... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM 16-39 NOTE Ignition Coil Primary Peak Voltage Inspection Starter Button Operation Check • Remove the seats (see Seat Removal in the Frame chap­ter). • Set the Hand Tester [A] to the × 25 V DC range, connect it to the IC igniter [B] lead as follows. Hand Tester (+) Terminal [C] —&... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM IC Igniter Operation Voltage Check NOTE OFollow the instructions in the manufacturer’s operation manual for the proper procedure for operating the ig­niter checker. OThe igniter checker can perform inspections by simu­lating the following dynamic characteristics: the igniter response in relating to the engine speed, interlock cir­cuit signals, tachometer signals, and engine overspeed limiter signals. OThe igniter checker cannot be used for... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM Ignition System Circuit Ignition System ELECTRICAL SYSTEM 16-33 Charging System Circuit Charging System ELECTRICAL SYSTEM CAUTION Do not apply more than 24 V to the regulator/recti­fier and do not leave the 24 V applied for more than a few seconds, or the unit will be damaged. • If the test light did not light when the 24 V was applied momentarily to the BR terminal, the regulator/rectifier is defective. Replace... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM 16-39 NOTE Ignition Coil Primary Peak Voltage Inspection Starter Button Operation Check • Remove the seats (see Seat Removal in the Frame chap­ter). • Set the Hand Tester [A] to the × 25 V DC range, connect it to the IC igniter [B] lead as follows. Hand Tester (+) Terminal [C] —&... [читать подробенее]


  • - Ignition System

    ELECTRICAL SYSTEM IC Igniter Operation Voltage Check NOTE OFollow the instructions in the manufacturer’s operation manual for the proper procedure for operating the ig­niter checker. OThe igniter checker can perform inspections by simu­lating the following dynamic characteristics: the igniter response in relating to the engine speed, interlock cir­cuit signals, tachometer signals, and engine overspeed limiter signals. OThe igniter checker cannot be used for... [читать подробенее]