Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Maintenance Procedure
просмотров - 203

Brakes

Complete cleaning and drying the chain within 10 minutes.

Any other cleaning solution such as gasoline or trichloroethylene will cause deterioration and swelling of the O-ring.

Blow the chain dry with compressed air immedi­ately after cleaning.

• Apply oil to the sides of the rollers so that oil will penetrate to the rollers and bushings. Apply the oil to the O-rings so that the O-rings will be coated with oil.

• Wipe off any excess oil.

Brake Fluid Leak (Brake Hose and Pipe) Inspection

• Apply the brake lever or pedal and inspect the brake fluid leak from the brake hoses [A] and fittings.

• If the brake fluid leaked from any position, inspect or re­place the problem part.

2-28Периодический ремонт

Brake Hose Damage and Installation Condition Inspection

• Inspect the brake hose and fittings for deterioration, cracks and signs of leakage.

OThe high pressure inside the brake line can cause fluid to leak [A] or the hose to burst if the line is not properly main­tained. Bend and twist the rubber hose while examining it.

Replace the hose if any cracks [B] or bulges [C] are no­ ticed.

•Tighten any loose fittings and any banjo bolts.

Torque-Brake Hose Banjo Bolts: 34 N·m (3.5 kgf·m, 25 ft·lb)

       
   

• Inspect the brake hose routing.

+

If any brake hose routing is incorrect, route the brake hose according to Cable, Wire and Hose Routing Section in the Appendix chapter.

Brake Operation Inspection

• Inspect the operation of the front and rear brake by run­ning the vehicle on the dry road.

• If the brake operation is insufficiency, inspect the brake system.


Читайте также


  • - Maintenance Procedure

    NOTE L (When engine is completely dry) L (When filter is removed) Engine Oil Grade: API SE, SF, SG or API SH or SJ with JASO MA Viscosity: SAE 10W40 Capacity: 2.8 L (When filter is not removed)&... [читать подробенее]


  • - Maintenance Procedure

    NOTE &... [читать подробенее]


  • - Maintenance Procedure

    NOTE Total Amount 1.7 L (1.8 US qt) Maintenance Procedure CAUTION NOTE Coolant Filling • Install the drain plug [A]. Always replace the gasket with a new one. • Tighten the drain plug. Torque -Coolant Drain Plug: 11 N·m (1.1 kgf·m, 95 in·lb) • Fill [A] the radiator up to the bottom of the radiator filler neck [B] with coolant [C], and install the cap turning it clockwise about 1/4 turn.&... [читать подробенее]


  • - Maintenance Procedure

    Fourth Step • Set the dimmer switch [A] to low beam position. • Start the engine. • The low beam headlight and license plate light should go on. • If the low beam headlight and license plate light do not go on, inspect or replace the following item. Headlight Low Beam Bulb (see Lighting System in the Electrical System chapter) License Plate Light Bulb Headlight Fuse 10 A (see Fuses in the Electrical System chapter) Dimmer Switch (see Switch Inspection in the... [читать подробенее]


  • - Maintenance Procedure

    Third Step Second Step • Turn the ignition switch to P (Park) position. • The city light and taillight should go on. • If the light does not go on, inspect or replace the following item. Ignition Switch (see Switch Inspection in the Electrical System chapter)• Turn on the turn signal switch [A] (left or right position). • The left or right turn signal lights [B] (front and rear) ac­cording to the switch position should flash. • The turn signal indicator LED [C]... [читать подробенее]


  • - Maintenance Procedure

    NOTE Others Second Step First Step • Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to stop position [A]. • Push the starter button. • The engine does not start. • If the engine starts, inspect or replace the following item. Engine Stop Switch (see Switch Inspection in the Elec­trical System chapter)• Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to run... [читать подробенее]


  • - Maintenance Procedure

    Brakes Complete cleaning and drying the chain within 10 minutes. Any other cleaning solution such as gasoline or trichloroethylene will cause deterioration and swelling of the O-ring. Blow the chain dry with compressed air immedi­ately after cleaning.• Apply oil to the sides of the rollers so that oil will penetrate to the rollers and bushings. Apply the oil to the O-rings so that the O-rings will be coated with oil. • Wipe off any excess oil.Brake Fluid Leak (Brake Hose... [читать подробенее]


  • - Maintenance Procedure

    Suspension Front Forks/Rear Shock Absorber Operation Inspection • Pump the forks down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the forks do not smoothly or noise is found, inspect the fork oil level or fork clamps (see Front Fork Oil Change in the Suspension chapter). Периодический ремонт2-31 • Pump the seat down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the shock absorber does not smoothly stroke or noise... [читать подробенее]


  • - Maintenance Procedure

    Spark Plug Gap Lights and Switches Operation Inspection First Step • Turn on the ignition switch. The following lights should go on according to below table. 0.6 &... [читать подробенее]


  • - Maintenance Procedure

    Steering Play Adjustment NOTE О The cables and wiring will have some effect on the mo­tion of the fork which must be taken into account. Be sure the wires and cables are properly routed. OThe bearings must be in good condition and properly lubricated in order for any test to be valid.•Adjust the steering if necessary. • Remove: Handlebar (see Handlebar Removal in the Steering chapter) Side Cover (see Side Cover Removal in the Frame chap­ter) Seat (see Seat Removal in... [читать подробенее]