Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Maintenance Procedure
просмотров - 195

NOTE

Total Amount 1.7 L (1.8 US qt)

Maintenance Procedure

CAUTION

NOTE

Coolant Filling

• Install the drain plug [A]. Always replace the gasket with a new one.

• Tighten the drain plug.

Torque -Coolant Drain Plug: 11 N·m (1.1 kgf·m, 95 in·lb)

• Fill [A] the radiator up to the bottom of the radiator filler neck [B] with coolant [C], and install the cap turning it clockwise about 1/4 turn.

○Pour in the coolant slowly so that it can expel the air

from the engine and radiator. ○The radiator cap must be installed in two steps. First

turn the cap clockwise to the first stop. Then push down

on it and turn it the rest of the way.

Soft or distilled water must be used with the an­tifreeze (see Specifications) in the cooling system. If hard water is used in the system, it causes scales accumulation in the water passages, and consider­ably reduces the efficiency of the cooling system.

Периодический ремонт2-43

Water and Coolant Mixture Ratio (when shipping) Soft Water 50%

Coolant 50%

Freezing Point –35°C (–31°F)

○Choose a suitable mixture ratio by referring to the coolant manufacturer’s directions.

• Bleed the air from the cooling system while the engine is running.

○Start the engine with the radiator cap removed and run it until no more air bubbles [A] can be seen in the coolant.

○Tap the radiator hoses to force any air bubbles caught inside.

○Stop the engine and add coolant up to the radiator filler neck.

CAUTION
Do not add more coolant above the F level.
• Install: Engine Guard Left Side Cover Left Lower Fairing

• Install the radiator cap.

• Remove the reserve tank cap.

• Fill the reserve tank up to the H level [A] with coolant and install the cap.

2-44Периодический ремонт

Radiator Hoses and O-ring Replacement

• Drain the coolant (see Coolant Draining).

• Remove:

Lower Fairings (see Lower Fairing Removal in the Frame

chapter)

Spark Plug Caps

Thermostat Housing Cover [A]

Pipe [B]

Hoses [C]

O-rings [D]

To Cylinder Head [E]

To Carburetor [F]

To Cylinder [G]

• Apply grease to the new O-rings and install them.

• Install the hoses and tighten the clamps securely.

• Fill the coolant (see Coolant Filling). Check the cooling system for leaks.

Engine Oil Change

 

• Warm up the engine so that the oil will pick up any sedi­ment and drain easily. Then stop the engine.

• Support the motorcycle perpendicular to the ground, and place an oil pan beneath the engine.

• Remove the engine oil drain plug [A], and let the oil drain completely.

• If the oil filter is to be changed, replace it with a new one.

• Check the gasket at the drain plug for damage.

• Replace the gasket with a new one if it is damaged. After the oil has completely drained out, install the drain plug with the gasket, and tighten it.

Torque - Engine Oil Drain Plug: 29 N-m (3.0 kgf-m, 22 ft-lb)

Периодический ремонт2-45 Maintenance Procedure

• Fill the engine with a good quality motor oil specified in the table.

Torque - Oil Filler Plug: 1.5 N·m (0.15 kgf·m, 13 in·lb)

• Checktheoillevel.


Читайте также


  • - Maintenance Procedure

    NOTE L (When engine is completely dry) L (When filter is removed) Engine Oil Grade: API SE, SF, SG or API SH or SJ with JASO MA Viscosity: SAE 10W40 Capacity: 2.8 L (When filter is not removed)&... [читать подробенее]


  • - Maintenance Procedure

    NOTE &... [читать подробенее]


  • - Maintenance Procedure

    NOTE Total Amount 1.7 L (1.8 US qt) Maintenance Procedure CAUTION NOTE Coolant Filling • Install the drain plug [A]. Always replace the gasket with a new one. • Tighten the drain plug. Torque -Coolant Drain Plug: 11 N·m (1.1 kgf·m, 95 in·lb) • Fill [A] the radiator up to the bottom of the radiator filler neck [B] with coolant [C], and install the cap turning it clockwise about 1/4 turn.&... [читать подробенее]


  • - Maintenance Procedure

    Fourth Step • Set the dimmer switch [A] to low beam position. • Start the engine. • The low beam headlight and license plate light should go on. • If the low beam headlight and license plate light do not go on, inspect or replace the following item. Headlight Low Beam Bulb (see Lighting System in the Electrical System chapter) License Plate Light Bulb Headlight Fuse 10 A (see Fuses in the Electrical System chapter) Dimmer Switch (see Switch Inspection in the... [читать подробенее]


  • - Maintenance Procedure

    Third Step Second Step • Turn the ignition switch to P (Park) position. • The city light and taillight should go on. • If the light does not go on, inspect or replace the following item. Ignition Switch (see Switch Inspection in the Electrical System chapter)• Turn on the turn signal switch [A] (left or right position). • The left or right turn signal lights [B] (front and rear) ac­cording to the switch position should flash. • The turn signal indicator LED [C]... [читать подробенее]


  • - Maintenance Procedure

    NOTE Others Second Step First Step • Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to stop position [A]. • Push the starter button. • The engine does not start. • If the engine starts, inspect or replace the following item. Engine Stop Switch (see Switch Inspection in the Elec­trical System chapter)• Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to run... [читать подробенее]


  • - Maintenance Procedure

    Brakes Complete cleaning and drying the chain within 10 minutes. Any other cleaning solution such as gasoline or trichloroethylene will cause deterioration and swelling of the O-ring. Blow the chain dry with compressed air immedi­ately after cleaning.• Apply oil to the sides of the rollers so that oil will penetrate to the rollers and bushings. Apply the oil to the O-rings so that the O-rings will be coated with oil. • Wipe off any excess oil.Brake Fluid Leak (Brake Hose... [читать подробенее]


  • - Maintenance Procedure

    Suspension Front Forks/Rear Shock Absorber Operation Inspection • Pump the forks down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the forks do not smoothly or noise is found, inspect the fork oil level or fork clamps (see Front Fork Oil Change in the Suspension chapter). Периодический ремонт2-31 • Pump the seat down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the shock absorber does not smoothly stroke or noise... [читать подробенее]


  • - Maintenance Procedure

    Spark Plug Gap Lights and Switches Operation Inspection First Step • Turn on the ignition switch. The following lights should go on according to below table. 0.6 &... [читать подробенее]


  • - Maintenance Procedure

    Steering Play Adjustment NOTE О The cables and wiring will have some effect on the mo­tion of the fork which must be taken into account. Be sure the wires and cables are properly routed. OThe bearings must be in good condition and properly lubricated in order for any test to be valid.•Adjust the steering if necessary. • Remove: Handlebar (see Handlebar Removal in the Steering chapter) Side Cover (see Side Cover Removal in the Frame chap­ter) Seat (see Seat Removal in... [читать подробенее]