Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Строительство Maintenance Procedure
просмотров - 246

NOTE

L (When engine is completely dry)

L (When filter is removed)

Engine Oil

Grade: API SE, SF, SG or

API SH or SJ with JASO MA Viscosity: SAE 10W40 Capacity: 2.8 L (When filter is not removed)

○Although 10W-40 engine oil is the recommended oil for most conditions, the oil viscosity may need to be changed to accommodate atmospheric conditions in your riding area.

Oil Filter Replacement

• Support the motorcycle perpendicular to the ground.

• Remove the engine guard.

• Drain the engine oil (see Engine Oil Change).

• Using an oil filter wrench [A] on the oil filter [B], unscrew it.

Special Tool - Oil Filter Wrench: 57001-1249

• Replace the oil filter with a new one.

• Apply engine oil to the gasket before screwing on.

• Tighten the oil filter with an oil filter wrench or tighten it with hands about 3/4 turns after gasket touches the mounting surface of the engine.

Torque - Oil Filter: 17 N·m (1.7 kgf·m, 12.5 ft·lb)

• Pour in the specified type and amount of oil (see Engine Oil Change).

• Thoroughly warm up the engine and check for oil leakage.

Brake Hose Replacement

CAUTION

Brake fluid quickly ruins painted or plastic sur­faces; any spilled fluid should be completely wiped up immediately with wet cloth.

• When removing the brake hose, take care not to spill the brake fluid on the painted or plastic parts.

• When removing the brake hose, temporarily secure the end of the brake hose to some high place to keep fluid loss to a minimum.

• There are washers on each side of the brake hose fitting. Replace them with new ones when installing.

2-46Периодический ремонт

• When installing the hose, avoid sharp bending, kinking, flattening or twisting, and route the hose according to Ca­ble, Wire and Hose Routing in the Appendix chapter.

• Tighten the banjo bolts to the specified torque.

Torque - Brake Hose Banjo bolts: 34 N-m (3.5 kgf-m, 25 ft-lb)

• Bleed the brake line after installing the brake hose.

Brake Fluid Change

• Level the brake fluid reservoir.

• Remove the reservoir cap.

• Remove the rubber cap from the bleed valve [A] on the caliper.

• Attach a clear plastic hose [B] to the bleed valve, and run the other end of the hose into a container.

Fill the reservoir with fresh specified brake fluid.

• Change the brake fluid as follows:

• Repeat this operation until fresh brake fluid comes out from the plastic hose or the color of the fluid changes.


Читайте также


  • - Maintenance Procedure

    NOTE L (When engine is completely dry) L (When filter is removed) Engine Oil Grade: API SE, SF, SG or API SH or SJ with JASO MA Viscosity: SAE 10W40 Capacity: 2.8 L (When filter is not removed)&... [читать подробенее]


  • - Maintenance Procedure

    NOTE &... [читать подробенее]


  • - Maintenance Procedure

    NOTE Total Amount 1.7 L (1.8 US qt) Maintenance Procedure CAUTION NOTE Coolant Filling • Install the drain plug [A]. Always replace the gasket with a new one. • Tighten the drain plug. Torque -Coolant Drain Plug: 11 N·m (1.1 kgf·m, 95 in·lb) • Fill [A] the radiator up to the bottom of the radiator filler neck [B] with coolant [C], and install the cap turning it clockwise about 1/4 turn.&... [читать подробенее]


  • - Maintenance Procedure

    Fourth Step • Set the dimmer switch [A] to low beam position. • Start the engine. • The low beam headlight and license plate light should go on. • If the low beam headlight and license plate light do not go on, inspect or replace the following item. Headlight Low Beam Bulb (see Lighting System in the Electrical System chapter) License Plate Light Bulb Headlight Fuse 10 A (see Fuses in the Electrical System chapter) Dimmer Switch (see Switch Inspection in the... [читать подробенее]


  • - Maintenance Procedure

    Third Step Second Step • Turn the ignition switch to P (Park) position. • The city light and taillight should go on. • If the light does not go on, inspect or replace the following item. Ignition Switch (see Switch Inspection in the Electrical System chapter)• Turn on the turn signal switch [A] (left or right position). • The left or right turn signal lights [B] (front and rear) ac­cording to the switch position should flash. • The turn signal indicator LED [C]... [читать подробенее]


  • - Maintenance Procedure

    NOTE Others Second Step First Step • Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to stop position [A]. • Push the starter button. • The engine does not start. • If the engine starts, inspect or replace the following item. Engine Stop Switch (see Switch Inspection in the Elec­trical System chapter)• Turn on the ignition switch. • Set the neutral position. • Turn the engine stop switch to run... [читать подробенее]


  • - Maintenance Procedure

    Brakes Complete cleaning and drying the chain within 10 minutes. Any other cleaning solution such as gasoline or trichloroethylene will cause deterioration and swelling of the O-ring. Blow the chain dry with compressed air immedi­ately after cleaning.• Apply oil to the sides of the rollers so that oil will penetrate to the rollers and bushings. Apply the oil to the O-rings so that the O-rings will be coated with oil. • Wipe off any excess oil.Brake Fluid Leak (Brake Hose... [читать подробенее]


  • - Maintenance Procedure

    Suspension Front Forks/Rear Shock Absorber Operation Inspection • Pump the forks down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the forks do not smoothly or noise is found, inspect the fork oil level or fork clamps (see Front Fork Oil Change in the Suspension chapter). Периодический ремонт2-31 • Pump the seat down and up [A] 4 or 5 times, and inspect the smooth stroke. • If the shock absorber does not smoothly stroke or noise... [читать подробенее]


  • - Maintenance Procedure

    Spark Plug Gap Lights and Switches Operation Inspection First Step • Turn on the ignition switch. The following lights should go on according to below table. 0.6 &... [читать подробенее]


  • - Maintenance Procedure

    Steering Play Adjustment NOTE О The cables and wiring will have some effect on the mo­tion of the fork which must be taken into account. Be sure the wires and cables are properly routed. OThe bearings must be in good condition and properly lubricated in order for any test to be valid.•Adjust the steering if necessary. • Remove: Handlebar (see Handlebar Removal in the Steering chapter) Side Cover (see Side Cover Removal in the Frame chap­ter) Seat (see Seat Removal in... [читать подробенее]