Open Library - открытая библиотека учебной информации

Открытая библиотека для школьников и студентов. Лекции, конспекты и учебные материалы по всем научным направлениям.

Категории

Образование Battery
просмотров - 146

IGNITION SYSTEM

TROUBLESHOOTING

TRBL SHTG

POOR IDLE SPEED PERFORMANCE

A-2

TRBL SHTG

HEATER SYSTEM ELEC

AUTO CHOKE AND CARBURETTOR

M-11

HEATER SYSTEM ELEC

AUTO CHOKE AND CARBURETTOR

7. Wiring connection

+

5. Heater resistance
• Connect the tester (Ω x 1) to the heater
Tester (+) lead—( Black terminalØ Tester (-) lead—( Black terminalØ
  Automatic starter unit resistance: 16 - 24 Ω (20ºC)
 

6. Voltage
• Connect the pocket tester (DC20V) to the heater leads
Tester (+) lead—( Green/Red cable Tester (-) lead—( Black table
CORRECT

CORRECT

OUT OF SPECIFICATION

Replace the heater

OUT OF SPECIFICATION

Replace the heater

POOR CONNECTION

Check the connection of the heater entire system Refer to the “CIRCUIT DIAGRAM” section.

Correct

?
TRBL SHTG

STARTING FAILURE/HARD STARTING

NOTE:

Improperly charged battery Faulty battery

Ignition systemFaulty ignition unit Faulty pick up coil

The following troubleshooting does not cover all the possible causes of trouble. It should be helpful,

however, as a guide to troubleshooting. Refer to the relative procedure in this manual for inspection, adjustment and replacement of parts.

STARTING FAILURE/HARD STARTING


Читайте также


  • - Disconnect the connector (arrowed) and connect jumper wires to the positive and negative terminals of the battery

    Main engine relay terminal guide Test the fan relay (Nippondenso). With no voltage applied, there should be continuity between 1 and 2, and 3 and 4 - with voltage applied across 1 and 2, there should be NO continuity between 3 and 4 The switch (arrowed) for the cooling fan control on the thermostat cover On Bosch relays, disregard the terminal numbers, test it just like this Nippondenso relay connector from the cooling fan temperature... [читать подробенее]


  • - Battery

    Wiper blades Note:Fitting details for wiper blades vary according to model, and according to whether genuine Toyota wiper blades have been fitted. Use theprocedures and illustrations shown as a guide for your car. 1Check the condition of the wiper blades; if they are cracked or show any signs of deterioration, or if the glass swept area is smeared, renew them. Wiper blades should be renewed annually. 2To remove a windscreen wiper blade, lift the wiper arm, rotate the... [читать подробенее]


  • - Fill only with distilled water. Tap water contains minerals, which can damage the battery.

    ELECTRICAL SYSTEM Never attempt to repair a wheel CHECKING THE WHEEL After putting on a tyre, drive slowly for while to give the tyre trim time to adjust itself to the wheel. Failure to do so could lead to an accident, injury to the driver or damage to the scooter. CHK ADJ CHECKING THE BATTERY E-3 CHK ADJ FRONT: Size Type 120/70-12 51 L REAR: Size Type 130/70-12 56 L s WARNING: ... [читать подробенее]


  • - Battery

    IGNITION SYSTEM TROUBLESHOOTING TRBL SHTG POOR IDLE SPEED PERFORMANCE A-2 TRBL SHTG HEATER SYSTEM ELEC AUTO CHOKE AND CARBURETTOR M-11 HEATER SYSTEM ELEC AUTO CHOKE AND CARBURETTOR 7. Wiring connection + 5. Heater resistance • Connect the tester (&... [читать подробенее]


  • - Relay Circuit Inspection (with the battery disconnected)

    ELECTRICAL SYSTEM 16-63 Junction Box Fuse Circuit Inspection Junction Box ELECTRICAL SYSTEM The junction box [A] has fuses [B], relays, and diodes. The relays and diodes can not be removed. Junction Box Fuse Circuit Inspection • Remove the left side cover (see Side Cover Removal in the Frame chapter). Remove the junction box. Pull off the connectors from the junction box. • Make sure all connector terminals are clean and tight, and none of them... [читать подробенее]


  • - Relay Circuit Inspection (with the battery disconnected)

    ELECTRICAL SYSTEM 16-63 Junction Box Fuse Circuit Inspection Junction Box ELECTRICAL SYSTEM The junction box [A] has fuses [B], relays, and diodes. The relays and diodes can not be removed. Junction Box Fuse Circuit Inspection • Remove the left side cover (see Side Cover Removal in the Frame chapter). Remove the junction box. Pull off the connectors from the junction box. • Make sure all connector terminals are clean and tight, and none of them... [читать подробенее]


  • - If by chance an excessive amount of gas is generated due to overcharging, the safety valve operates to keep the battery safe.

    This battery is designed to sustain no unusual deterioration if refresh-charged according to the method specified above. Battery ELECTRICAL SYSTEM NOTE &... [читать подробенее]


  • - If by chance an excessive amount of gas is generated due to overcharging, the safety valve operates to keep the battery safe.

    This battery is designed to sustain no unusual deterioration if refresh-charged according to the method specified above. Battery ELECTRICAL SYSTEM NOTE &... [читать подробенее]


  • - Battery

    ELECTRICAL SYSTEM 16-19 Electrical Wiring ELECTRICAL SYSTEM Precautions ELECTRICAL SYSTEM 16-17 Male Connectors [B] Wiring Inspection • Visually inspect the wiring for signs of burning, fraying, etc. • If any wiring is in poor condition, replace the damaged wiring. • Pull each connector [A] apart and inspect it for corrosion, dirt, and damage. • If the connector is corroded or dirty, clean it carefully. If it is damaged,... [читать подробенее]


  • - Разряд NiCd / NiMH battery

    На этом экране показана установка тока разряда слева и конечное напряжение - справа. (Ток разряда колеблется от 0.1 до 1.0A и конечные напряжения от 0.1 до 25.0V). Чтобы запустить процесс, нажмите и удерживайте клавишу Start / Enter больше чем 3 секунды Этот экран отображает текущее... [читать подробенее]